Your Vehicle: 2009 Nissan-Datsun Altima V6-3.5L (VQ35DE)
 
Vehicle » A L L Diagnostic Trouble Codes ( DTC ) » Testing and Inspection » P Code Charts » P0442  
 
 
  P0442  
 

P0442 EVAP CONTROL SYSTEM

DTC Logic

DTC DETECTION LOGIC
This diagnosis detects leakage in the EVAP purge line using engine intake manifold vacuum.
If pressure does not increase, the ECM will check for leakage in the line between the fuel tank and EVAP canister purge volume control solenoid valve, under the following "Vacuum test" conditions.
The EVAP canister vent control valve is closed to shut the EVAP purge line off. The EVAP canister purge volume control solenoid valve will then be opened to depressurize the EVAP purge line using intake manifold vacuum. After this occurs, the EVAP canister purge volume control solenoid valve will be closed.

  

  

CAUTION:

  • Use only a genuine NISSAN fuel filler cap as a replacement. If an incorrect fuel filler cap is used, the MIL may illuminate.
  • If the fuel filler cap is not tightened properly, the MIL may illuminate.
  • Use only a genuine NISSAN rubber tube as a replacement.

DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds. TESTING CONDITION:
    • Perform "DTC WORK SUPPORT" when the fuel level is between 1/4 and 3/4 full, and vehicle is placed on flat level surface.
    • Always perform test at a temperature of 0 to 30°C (32 to 86°F) .

NOTE:
Check that EVAP hoses are connected to EVAP canister purge volume control solenoid valve properly.
Will CONSULT-III be used?
YES >> GO TO 2.
NO >> GO TO 3.
2.PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT-III

  1. Turn ignition switch ON.
  2. Turn ignition switch OFF and wait at least 10 seconds.
  3. Turn ignition switch ON and select "DATA MONITOR" mode with CONSULT-III.
  4. Check that the following conditions are met. COOLAN TEMP/S: 0 - 70°C (32 - 158°F)

INT/A TEMP SE: 0 - 30°C (32 - 86°F)

  1. Select "EVP SML LEAKAGE P0442/P1442" of "EVAPORATIVE SYSTEM" in "DTC WORK SUPPORT" mode with CONSULT-III. Follow the instructions displayed.

NOTE:
If the engine speed cannot be maintained within the range displayed on the CONSULT-III screen, go to See: Powertrain Management\Computers and Control Systems\Testing and Inspection\Programming and Relearning\Basic Inspection.
Which is displayed on CONSULT-III screen?
OK >> Inspection END
NG >> Go to Diagnosis Procedure.
3.PERFORM COMPONENT FUNCTION CHECK
With GST

NOTE:
Be sure to read the explanation of DRIVING PATTERN in See: Powertrain Management\Computers and Control Systems\Testing and Inspection\Programming and Relearning\How To Set SRT Code before driving vehicle.

  1. Start engine.
  2. Drive vehicle according to DRIVING PATTERN.
  3. Stop vehicle.
  4. Turn ignition switch OFF and wait at least 10 seconds.
  5. Turn ignition switch ON.
  6. Turn ignition switch OFF and wait at least 10 seconds.
  7. Turn ignition switch ON.
  8. Check 1st trip DTC. Is 1st trip DTC displayed?

YES-1 >> P0441: Go to See: P0441.
YES-2 >> P0442: Go to Diagnosis Procedure.
NO >> Inspection END

Diagnosis Procedure
1.CHECK FUEL FILLER CAP DESIGN

  1. Turn ignition switch OFF.

  

  1. Check for genuine NISSAN fuel filler cap design. Is the Inspection result normal?

YES >> GO TO 2.
NO >> Replace with genuine NISSAN fuel filler cap.
2.CHECK FUEL FILLER CAP INSTALLATION
Check that the cap is tightened properly by rotating the cap clockwise.
Is the Inspection result normal?
YES >> GO TO 3.
NO >> Open fuel filler cap, then clean cap and fuel filler neck threads using air blower. Retighten until ratcheting sound is heard.
3.CHECK FUEL FILLER CAP FUNCTION
Check for air releasing sound while opening the fuel filler cap.
Is the Inspection result normal?
YES >> GO TO 5.
NO >> GO TO 4.
4.CHECK FUEL TANK VACUUM RELIEF VALVE
Refer to Component Inspection.
Is the Inspection result normal?
YES >> GO TO 5.
NO >> Replace fuel filler cap with a genuine one.
5.CHECK FOR EVAP LEAKAGE
Refer to See: Powertrain Management\Emission Control Systems\Evaporative Emissions System\Testing and Inspection\EVAP Leak Check.
Is there any leakage in EVAP line?
YES >> Repair or replace malfunctioning part.
NO >> GO TO 6.
6.CHECK EVAP CANISTER VENT CONTROL VALVE
Check the following.

YES >> GO TO 7.
NO >> Repair or replace EVAP canister vent control valve and O-ring.
7.CHECK IF EVAP CANISTER IS SATURATED WITH WATER

  

Remove EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor attached.
Does water drain from the EVAP canister?
YES >> GO TO 8.
NO-1 >> With CONSULT-III: GO TO 10.
NO-2 >> Without CONSULT-III: GO TO 11.
8.CHECK EVAP CANISTER
Weigh the EVAP canister with the EVAP canister vent control valve and EVAP control system pressure sensor attached.
The weight should be less than 2.1 kg (4.6 lb).
Is the Inspection result normal?
YES-1 >> With CONSULT-III: GO TO 10.
YES-2 >> Without CONSULT-III: GO TO 11.
NO >> GO TO 9.
9.DETECT MALFUNCTIONING PART
Check the following.

  • EVAP canister for damage
  • EVAP hose between EVAP canister and vehicle frame for clogging or poor connection >> Repair hose or replace EVAP canister.

10.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OPERATION
With CONSULT-III

  1. Disconnect vacuum hose from EVAP canister purge volume control solenoid valve at EVAP service port.
  2. Start engine.
  3. Perform "PURG VOL CONT/V" in "ACTIVE TEST" mode.
  4. Touch "Qu" on CONSULT-III screen to increase "PURG VOL CONT/V" opening to 100%.
  5. Check vacuum hose for vacuum.

Vacuum should exist.

Is the Inspection result normal?
YES >> GO TO 13.
NO >> GO TO 12.
11.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OPERATION
Without CONSULT-III

  1. Start engine and warm it up to normal operating temperature.
  2. Stop engine.
  3. Disconnect vacuum hose from EVAP canister purge volume control solenoid valve at EVAP service port.
  4. Start engine and let it idle for at least 80 seconds.
  5. Check vacuum hose for vacuum when revving engine up to 2,000 rpm.

Vacuum should exist.

Is the Inspection result normal?
YES >> GO TO 13.
NO >> GO TO 12.
12.CHECK VACUUM HOSE
Check vacuum hoses for clogging or disconnection. Refer to See: Powertrain Management\Emission Control Systems\Evaporative Emissions System\Description and Operation\System Diagram.
Is the Inspection result normal?
YES >> GO TO 13.
NO >> Repair or reconnect the hose.
13.CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
Refer to See: P0443.
Is the Inspection result normal?
YES >> GO TO 14.
NO >> Replace EVAP canister purge volume control solenoid valve.
14.CHECK FUEL TANK TEMPERATURE SENSOR
Refer to See: P0181.
Is the Inspection result normal?
YES >> GO TO 15.
NO >> Replace fuel level sensor unit and fuel pump.
15.CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
Refer to See: P0451.
Is the Inspection result normal?
YES >> GO TO 16.
NO >> Replace EVAP control system pressure sensor.
16.CHECK EVAP PURGE LINE
Check EVAP purge line (pipe, rubber tube, fuel tank and EVAP canister) for cracks or improper connection. Refer to See: Powertrain Management\Emission Control Systems\Evaporative Emissions System\Description and Operation\System Diagram.
Is the Inspection result normal?
YES >> GO TO 17.
NO >> Repair or reconnect the hose.
17.CLEAN EVAP PURGE LINE
Clean EVAP purge line (pipe and rubber tube) using air blower.
>> GO TO 18.
18.CHECK EVAP/ORVR LINE
Check EVAP/ORVR line between EVAP canister and fuel tank for clogging, kinks, looseness and improper connection. For location, refer to See: Powertrain Management\Emission Control Systems\Evaporative Emissions System\Testing and Inspection\Evap Canister\Diagnosis Procedure.
Is the Inspection result normal?
YES >> GO TO 19.
NO >> Repair or replace hoses and tubes.
19.CHECK RECIRCULATION LINE
Check recirculation line between fuel filler tube and fuel tank for clogging, kinks, cracks, looseness and improper connection.
Is the Inspection result normal?
YES >> GO TO 20.
NO >> Repair or replace hose, tube or fuel filler tube.
20.CHECK REFUELING EVAP VAPOR CUT VALVE
Refer to See: Powertrain Management\Emission Control Systems\Refueling Vapor Recovery System\Testing and Inspection.
Is the Inspection result normal?
YES >> GO TO 21.
NO >> Replace refueling EVAP vapor cut valve with fuel tank.
21.CHECK FUEL LEVEL SENSOR
Refer to See: Instrument Panel, Gauges and Warning Indicators\Testing and Inspection\Component Tests and General Diagnostics\Fuel Level Sensor Signal Circuit\Component Inspection.
Is the Inspection result normal?
YES >> GO TO 22.
NO >> Replace fuel level sensor unit and fuel pump.
22.CHECK INTERMITTENT INCIDENT
Refer to See: Testing and Inspection\Initial Inspection and Diagnostic Overview\Service Information For Electrical Incident\Intermittent Incident.
>> Inspection END

Component Inspection
1.CHECK FUEL FILLER CAP

  1. Turn ignition switch OFF.
  2. Remove fuel filler cap.

  

  1. Wipe clean valve housing.
  2. Install fuel filler cap adapter (commercial service tool) to fuel filler cap.

  

  1. Check valve opening pressure and vacuum.

  

Is the Inspection result normal?
YES >> Inspection END
NO >> GO TO 2.
2.REPLACE FUEL FILLER CAP
Replace fuel filler cap.

CAUTION:
Use only a genuine fuel filler cap as a replacement. If an incorrect fuel filler cap is used, the MIL may illuminate.
>> Inspection END