Your Vehicle: 2009 Nissan-Datsun Altima V6-3.5L (VQ35DE)
 
Vehicle » Powertrain Management » Relays and Modules - Powertrain Management » Technical Service Bulletins » All Technical Service Bulletins » Engine Controls - ECM Replacement Procedures » Service Procedure  
 
 
  Service Procedure  
 

Check NATS On The Vehicle

1. Check to see if the vehicle you're working on has "ECM based" NATS V2.0 or V5.0.

a. If the vehicle has ECM based NATS V2.0 or V5.0, it will NOT start after you install a service replacement ECM. So you'll have to re-register all ignition keys, including spare keys with CONSULT-II and the purple NATS card. After you do this, proceed with step 2.

^ If you do not know how to re-register the keys, refer to the ESM for the NATS key re-registration procedure.

b. If the vehicle has "BCM based" NATS (instead of ECM based NATS V2.0 or V5.0), you do NOT have to re-register the ignition or spare keys. Proceed with step 2.

Check For ECM Data Updates in ASIST

  

2. In ASIST, select [CONSULT Utilities] >>> [ECM/TCM Data]. Then choose Model and Model Year (see Figure 1).

3. Look for ECM Data Updates (listed by ECM P/Ns and vehicle configuration) in the top, center display panel of the ASIST screen (see Figure 1).

a. If there is not updates listed for your vehicle configuration, you do NOT have to reprogram the service replacement ECM. Proceed with step 5.

b. If there is updates listed for your vehicle configuration, see if they apply to the service replacement ECM you're going to install. Do this by performing step 4.

4. Select the "configuration" on the screen for the vehicle you're working on. Then confirm that your ECM is listed in the "Replaces 23710-XXXXX, -XXXXX, etc" section in the lower, center "Details" panel of the ASIST screen (see Figure 1).

a. If your ECM is listed in the "Details" panel, you must reprogram the ECM with the latest data update. After you do this, proceed with step 5.

CAUTION: The 1999-2000 Frontier and 1999-2000 Pathfinder have a gray CONSULT connector AND a white GST connector. Do NOT attempt to perform the ECM Reprogramming procedure with CONSULT-II connected to the gray CONSULT connector. See the appropriate ESM for further details if necessary.

b. If your ECM is NOT listed in the "Details" panel, you do NOT have to reprogram the ECM. Proceed with step 5.

Accelerator Pedal & Throttle Valve Closed Position Learning

5. Perform the Accelerator Pedal & Throttle Valve Closed Position Learning as follows:

a. Make sure the accelerator pedal is fully released.

b. Turn the ignition switch "ON" for 2 seconds.

c. Turn the ignition switch "OFF" for 10 seconds.

d. Turn the ignition switch "ON" for 2 seconds, then

  

e. Turn the ignition switch "OFF" again for 10 seconds (see Figure 2).

f. Proceed with step 6.

Perform Idle Air Volume Learning (IAVL)

NOTE: Make sure all electrical loads are turned OFF, including A/C, defroster, radio, lights, etc. while performing the following procedures. Also, make sure the engine cooling fans are NOT operating during the following procedures.

6. Perform the Idle Air Volume Learning procedure as follows:

a. Connect CONSULT-II to the vehicle.

b. Warm up engine and transmission to operating temperature.

  

c. In the [CONSULT WORK SUPPORT] mode, select [IDLE AIR VOL LEARN]. See Figure 3.

NOTE:
^ If IDLE AIR VOL LEARN is not shown as a SELECT WORK ITEM on CONSULT, the vehicle does not need the procedure.

^ In this case only, this bulletin is complete, no further action is needed.

  

d. Press [START] on the "IDLE AIR VOL LEARN" screen. See Figure 4.

  

e. Press [START] on the "WORK SUPPORT" screen to begin the Idle Air Volume Learning (IAVL) procedure. See Figure 5.

^ The IAVL procedure will take several minutes to complete.

  

^ CONSULT will display "Please Wait" in the center of the screen while the IAVL procedure is in process. See Figure 6.

  

^ CONSULT will display "CMPLT" in the top right corner of the screen when the IAVL procedure is finished. See Figure 7.

f. Once the IAVL procedure is finished, proceed with step 7.

For 2005 and Later MY Vehicles ONLY: Enter VIN Into New Service Replacement ECM

7. Enter the VIN into the new service replacement ECM as follows:

  

a. Select [ENGINE] on the "Select System" screen. See Figure 8.

  

b. Select [WORK SUPPORT] on the "Select Diag Mode" screen. See Figure 9.

  

C. Scroll down and select [VIN REGISTRATION] on the "Select Work Item" screen. See Figure 10.

  

d. Press [START] on the "VIN Registration" screen. See Figure 11.

  

e. Select [INPUT] on the "VIN Registration" screen. See Figure 12.

  

f. Enter the entire VIN using the keyboard. See Figure 13.

^ Use [CHNG] to switch between the letters and numbers keyboard screens.

  

g. Once the entire VIN is entered, select [ENTER] on the "Keyboard" screen. See Figure 14.

  

h. Select [INPUT] on the "VIN Registration" screen and enter the entire VIN again. See Figure 15.

^ You MUST enter the VIN a second time for confirmation purposes.

  

i. Once the entire VIN is entered (a second time), select [ENTER] on the "Keyboard" screen. See Figure 16.

  

j. Select [START] on the "VIN Registration" screen to complete the VIN registration process. See Figure 17.

k. Turn the ignition switch OFF and wait at least 10 seconds.